MembraneGuard MG 11 Silt Remover
Part No. RXSOL-33-1523-025
RO Membrane Silt Cleaner
Remove organics, silt and other particulate deposits from polyamide, polysulfone and thin film composite membrane surfaces
Key details
| Part number | RXSOL-33-1523-025 |
|---|---|
| Generic name | RO Membrane Silt Cleaner |
| Standard packing | 25.00 Kg.PWD |
Need this product at your port or plant?
Enquire Now<div id="cke_pastebin">
All polyamide, polysulfone, and thin-film composite membranes can be used with MembraneGuard MG 11 Silt Remover. It can be used at any temperature up to the highest that the membrane manufacturer recommends, starting at 15°C (60°F). Twenty-five grams of MembraneGuard MG 11 Silt Remover are diluted with one liter of water as the standard.</div>
<p>
Dosage: 25 gm per ltr of water</p>
<p>
How to use MembraneGuard MG 11 Silt Remover:</p>
<ul>
<li>
Add RO permeate to the cleaning tank.</li>
<li>
Add 25 grams of Floclean MC11 gradually for every liter of available cleaning tank space.</li>
<li>
The cleaning solution can be heated to increase cleaning efficacy.</li>
<li>
Use a mixer to thoroughly mix the solution or run it through the cleaning pump.</li>
<li>
Adhere to the temperature restrictions set by the membrane manufacturer.</li>
<li>
For one hour, follow the flow rate suggested by the membrane or system manufacturer and circulate the solution through the membrane bank in the feed direction.</li>
</ul>
<p>
The following recommendations may be followed in the event that the manufacturer's advice is unavailable.</p>
<h2>
Spiral Wound Membrane</h2>
<table border="0" cellpadding="1" cellspacing="1" style="width: 400px;">
<thead>
<tr>
<th scope="col">
<p>
Membrane Diameter in inches</p>
<p>
</p>
</th>
<th scope="col">
<p>
Flow rate in ltrs/min</p>
<p>
</p>
</th>
</tr>
</thead>
<tbody>
<tr>
<td>
4</td>
<td>
23</td>
</tr>
<tr>
<td>
6</td>
<td>
53</td>
</tr>
<tr>
<td>
8</td>
<td>
91</td>
</tr>
<tr>
<td>
10</td>
<td>
114</td>
</tr>
<tr>
<td>
12</td>
<td>
204</td>
</tr>
</tbody>
</table>
<p>
</p>
<h2>
Hollow Fiber Membrane</h2>
<table border="0" cellpadding="1" cellspacing="1" style="width: 400px;">
<thead>
<tr>
<th scope="col">
<p>
Membrane Diameter in inches</p>
<p>
</p>
</th>
<th scope="col">
<p>
Flow rate in ltrs/min</p>
<p>
</p>
</th>
</tr>
</thead>
<tbody>
<tr>
<td>
4</td>
<td>
19</td>
</tr>
<tr>
<td>
8</td>
<td>
57</td>
</tr>
<tr>
<td>
10</td>
<td>
76</td>
</tr>
</tbody>
</table>
<p>
</p>
<p>
To avoid the removed solids from redepositing, the first return flow—up to 15% of the cleaning tank volume—should be routed to the drain in cases of severe fouling. For multi-pass systems, cleaning each pass independently will get the greatest results. If the removed material causes the solution to become turbid or discolored, it should be thrown out. Before cleaning more passes, a new solution needs to be made. Before putting the system back in service, rinse it with permeate.</p>
Need MembraneGuard MG 11 Silt Remover for your operation?
Our team helps with product selection, dosage, safety data and delivery worldwide.
Request a Quote